Sealand S Series Vacuum Pump Manuel d'utilisateur télécharger pdf

Dimensional

Speciﬁ cations

Model Volts (DC)

Avg. Amp Draw

GPH

Fuse/Breaker

Wire Size

Weight

S12

12 6

225 10 Amp 12-14 Ga.

8 Lbs.

S24

24 3 225 5 Amp 14-16 Ga. 8 Lbs.

Before mounting the pump, you must

consider the following:

1. Vacuum pump must be mounted

horizontally only.

2. The pump can be mounted from

2 to 15 feet from the vacuum tank.

The maximum distance is 15 feet.

3. The vacuum pump must not be mount-

ed more than 3 feet higher than the

vacuum tank outlet.

4. The maximum head pressure on the

discharge of the pump must not exceed

6 feet.

Note: Two-toilet systems require a

vacuum pump and vacuum tank for each

toilet. It is our experience that this method

provides the beneﬁ t of a totally redundant

operating toilet in case of failure in one

toilet, and two pumps greatly reduce hose runs and system complexity.

Make sure the vacuum pump is properly located before proceeding. Place the vacuum pump on the surface to

be mounted. Position as needed. Using a center punch, mark the four slotted holes in the pump feet. Remove

pump.

Note: The vacuum pump emits a low frequency vibration that sometimes can produce a noticeable noise. The

best method of isolating the pump from the mounting surface is to use SeaLand’s Noise Isolation Kit #319053.

This kit consists of two pieces of pre-cut isolator hose and fasteners. If using Noise Isolation Kit, the pump should

be mounted to hose isolators then the hose isolators mounted to the ﬂ oor.

Using a 3/16-inch drill bit, drill the four mounting holes. Use a #14 wood screw to secure pump.

The ﬂ ow direction is indicated on the pump body.

Reminder: Never mount the pump on its side, at an angle or upside down. For proper operation, the pump must

be mounted horizontally.

Reminder: The best system will position the vacuum pump at the same level or lower than the vacuum tank and

the vacuum tank will be positioned at the same level or lower than the VacuFlush toilet.

Stainless steel wall mounting bracket available as optional accessory – P/N 341505.

Typical One and Two Toilet Installation

Electrical

Speciﬁ cations

S-Series Vacuum Pump

Installation Instructions

Dometic Corporation • Sanitation Systems

13128 State Rt. 226, P.O. Box 38

Big Prairie, OH 44611-0038 USA

330-496-3211

1-800-321-9886 • Fax: 330-496-3097

® Registered; ™ Trademark of Dometic Corporation

1 2

Résumé du contenu

Page 1 - Installation Instructions

Dimensional Speciﬁ cationsModel Volts (DC)Avg. Amp DrawGPHFuse/BreakerWire SizeWeightS1212 6225 10 Amp 12-14 Ga.8 Lbs.S2424 3 225 5 Amp 14-16 Ga. 8 Lb

Page 2

Wire the S-Pump as shown in the wiring diagram. Use multistranded copper wire. Protect the wiring by installing grommets or other protective device

Commentaires sur ces manuels

Pas de commentaire

Sealand S Series Vacuum Pump Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Sealand S Series Vacuum Pump. SeaLand S Series Vacuum Pump User Manual [pl] [en] [de] [cs] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Sealand S Series Vacuum Pump